10 Basic Electronics Projects for Beginners, with Parts Lists
The best basic electronics projects start with a battery, a breadboard, and a few parts. Build an LED circuit first, then add buttons, capacitors, transistors, and timers. These ten projects include exact parts lists and wiring steps, so you can learn one idea at a time without soldering.
Before you start
Every build uses one 9V battery, a battery snap, jumper wires, and a solderless breadboard. Reuse these throughout. Choose an 830-contact breadboard. A digital multimeter helps check voltage and resistance. Alligator clips can hold temporary connections.
Connect battery positive to the positive rail and battery negative to the ground rail. Ground here means battery negative. Check whether each rail is split. Five-hole groups are connected internally; opposite sides of the center gap are separate.
Use standard red indicator LEDs, 1/4W resistors, and capacitors rated at least 16V. Resistors and LEDs are available in our components section; the shopping list below links to each part. An LED's longer lead is usually its anode; the flat body edge marks its cathode.
Safety: Disconnect the battery before changing wires. Never connect the rails together directly. Check electrolytic capacitor polarity before powering up. Stop if anything becomes hot. Keep batteries and loose parts away from small children. Use battery power only, never household mains wiring.
Shopping list for all ten projects
Most of these parts are reused from project to project. Items with a price are in our store; prices are read from the store each night.
| Part | Used in | Where to get it |
|---|---|---|
| 830-contact solderless breadboard | All | MB-102 breadboard, $6.50 |
| 9V battery snap (and a 9V battery) | All | 9V battery snap connectors, $4.99 |
| Jumper wires | All | Jumper wire set, $6.99 |
| Red LEDs (2) | 1 to 8, 10 | 5mm red LED, $3.99 |
| Resistors: 1kΩ (3), 2.2kΩ, 10kΩ, 22kΩ, 33kΩ, 47kΩ, 68kΩ, 100kΩ, 4.7MΩ, 10MΩ | All | Resistors |
| Momentary push-button, normally open | 2, 5, 6 | Tactile push-button switch, $3.25 |
| 10kΩ potentiometer | 3 | The 10kΩ trimmer in our trimmer potentiometer kit ($4.99) fits a breadboard |
| Electrolytic capacitors: 1,000µF, 470µF, 22µF, 10µF | 5, 8 | 1000µF, 10µF, and more under Capacitors |
| Ceramic capacitors: 10nF (2), 100nF | 8, 9 | Capacitors |
| 2N3904 NPN transistors (2) | 6, 7, 10 | 2N3904 transistors, pack of 10, $3.99 |
| Photoresistor (CdS photocell) | 7 | Cadmium-sulfide photocells, pack of 5, $5.99 |
| NE555 timer chip, 8-pin DIP | 8, 9 | ICs and sensors |
| Passive piezo sounder | 9 | Electronic components |
| Digital multimeter (recommended) | Checking your work | 7-function digital multimeter, $15.99 |
Prefer one box with a book to follow? Make: Electronics 3rd Edition Kit 1 ($68.99) covers the same ideas in order.
Calculate an LED resistor
R = (Vs - Vf) / I. Vs is supply voltage, Vf is LED forward voltage, and I is current in amperes. For a red LED with an assumed 2V forward drop at 7mA: R = (9 - 2) / 0.007 = 1,000Ω. Use 1kΩ. Actual LED voltage varies.
1. Light one LED
Teaches: Polarity and current limiting.
Parts: One red LED and one 1kΩ resistor, plus the shared supplies above.
- Place the LED with its leads in separate connected groups.
- Connect the positive rail to one end of the resistor.
- Connect the resistor's other end to the LED anode.
- Connect the LED cathode to ground. Attach the battery.
What you should see: A steady light. If it stays dark, disconnect power and check its orientation.
Try this: Replace 1kΩ with 2.2kΩ. The lower current usually makes the LED dimmer.
2. Add a push-button
Teaches: An open switch interrupts current.
Parts: One red LED, one 1kΩ resistor, and one normally open momentary push-button.
- Connect positive to one switch contact.
- Connect the other contact to the resistor.
- Connect the resistor's free end to the LED anode.
- Connect the cathode to ground.
What you should see: The LED lights only while you press. Four-leg buttons have internally paired legs. With power disconnected, use continuity mode to identify contacts that connect only when pressed.
Try this: Add a second normally open button in series. Both must be pressed.
3. Make a potentiometer LED dimmer
Teaches: Variable resistance controls current.
Parts: One red LED, one 1kΩ resistor, and one 10kΩ linear potentiometer.
- Connect positive to the 1kΩ resistor.
- Connect its other end to one outer potentiometer terminal.
- Connect the center terminal, called the wiper, to the LED anode.
- Connect the unused outer terminal to the wiper. Connect the LED cathode to ground.
What you should see: Turning the shaft changes brightness. The fixed resistor limits current even at minimum potentiometer resistance.
Try this: Swap which outer terminal connects to the fixed resistor, keeping the unused terminal joined to the wiper. The turning direction reverses.
4. Compare series and parallel LEDs
Teaches: Series components share current; parallel branches provide separate paths.
Parts: Two red LEDs and two 1kΩ resistors.
- For series wiring, connect positive through one resistor to LED A's anode.
- Connect A's cathode to LED B's anode. Connect B's cathode to ground.
- Observe, then disconnect power and dismantle this circuit.
- For parallel wiring, connect positive through one resistor to A's anode, then A's cathode to ground.
- Build a separate identical branch for B using the second resistor.
What you should see: Both arrangements light both LEDs. Brightness can differ because the resistor voltage differs.
Try this: Disconnect one LED. In series, both go out. In parallel, the other branch stays lit. Always give parallel LEDs separate resistors.
5. Store charge and fade an LED
Teaches: A capacitor stores energy and releases it through a load.
Parts: One red LED, two 1kΩ resistors, one normally open button, and one 1,000µF electrolytic capacitor.
- Choose a connected hole group called node A. Connect capacitor positive to A and its striped negative lead to ground.
- Connect positive through the button, then through one resistor, to A.
- Connect A through the second resistor to the LED anode.
- Connect the cathode to ground. Power up and hold the button for five seconds.
- Release the button.
What you should see: The LED lights while charging, then fades after release. The capacitor continues supplying current briefly.
Try this: Use 470µF instead. The fade becomes shorter. Discharge the capacitor through a 1kΩ resistor before rebuilding.
6. Control an LED with a transistor
Teaches: Base current controls a larger collector current.
Parts: One 2N3904 NPN transistor, one red LED, one button, and 1kΩ, 10kΩ, and 100kΩ resistors.
On a 2N3904 in the usual TO-92 package, hold the flat face toward you with the leads pointing down: the leads are emitter, base, collector from left to right. Confirm against the manufacturer's datasheet for your part. Never assume different transistor models share a pin order.
- Connect the emitter to ground.
- Connect positive through 1kΩ to the LED anode. Connect the cathode to the collector.
- Connect positive through the button and 10kΩ resistor to the base.
- Connect 100kΩ between base and ground.
What you should see: Pressing the button turns on the LED. The 100kΩ resistor helps hold the transistor off when released.
Try this: Replace the 10kΩ base resistor with 47kΩ and compare brightness.
7. Build a light-activated LED
Teaches: A resistance divider can turn changing light into a control voltage.
Parts: One 2N3904, one red LED, 1kΩ, 10kΩ, and 47kΩ resistors, and one photoresistor measuring roughly 10kΩ or less under bright light and over 1MΩ when covered.
- Connect emitter to ground. Connect positive through 1kΩ to the LED anode, with cathode to collector.
- Connect one photoresistor leg to positive and the other to a new node B.
- Connect 47kΩ from B to ground.
- Connect 10kΩ from B to the transistor base.
What you should see: Bright light turns the LED on. Covering the photoresistor turns it off or makes it much dimmer. Response depends on the sensor and room lighting.
Try this: Replace 47kΩ with 22kΩ. More light should be needed to turn it on.
8. Blink an LED with a 555 timer
Teaches: A timer can generate repeating pulses.
Parts: One NE555 in an eight-pin DIP package, one red LED, two 1kΩ resistors, one 68kΩ resistor, and 10µF electrolytic, 10nF ceramic, and 100nF ceramic capacitors.
Viewed from above with the notch upward, pin 1 is upper left. Numbering runs counterclockwise. Confirm against the datasheet for your chip.
- Place the chip across the center gap. Connect pin 1 to ground; pins 8 and 4 to positive.
- Connect 100nF between pins 8 and 1, close to the chip. Connect 10nF from pin 5 to ground.
- Join pins 2 and 6. Connect 10µF positive to this junction and negative to ground.
- Connect R1, 1kΩ, from positive to pin 7. Connect R2, 68kΩ, from pin 7 to the pins 2/6 junction.
- Connect pin 3 through the remaining 1kΩ resistor to the LED anode. Connect cathode to ground.
What you should see: About one flash per second. The estimate is f ≈ 1.44 / ((R1 + 2R2) × C), with resistance in ohms and capacitance in farads.
Try this: Replace the 10µF timing capacitor with 22µF for slower blinking.
9. Turn the timer into a tone generator
Teaches: Faster pulses become audible sound.
Parts: The previous timer circuit, one additional 10nF ceramic capacitor, one 1kΩ resistor, and one passive piezo sounder rated for at least 9V drive. Use a passive type without an internal oscillator.
- Disconnect power. Remove the LED and its series resistor.
- Replace only the 10µF timing capacitor at pins 2/6 with the additional 10nF capacitor.
- Connect pin 3 through 1kΩ to one piezo terminal. Connect its other terminal to ground.
- Retain all other timer connections and reconnect power.
What you should hear: A tone around 1kHz. Loudness varies by sounder. Do not substitute an ordinary low-impedance speaker.
Try this: Replace the 68kΩ timing resistor with 33kΩ for a higher pitch.
10. Make a two-transistor touch switch
Teaches: Two transistors can amplify a small input current.
Parts: Two 2N3904 transistors labeled Q1 and Q2, one red LED, 1kΩ, 100kΩ, and 10MΩ resistors, and two bare jumper ends as touch contacts.
- Connect Q2 emitter to ground and Q1 emitter to Q2 base.
- Join both collectors. Connect positive through 1kΩ to the LED anode, with cathode to the joined collectors.
- Connect Q1 base to touch contact B and through 10MΩ to ground.
- Connect positive through 100kΩ to touch contact A. Keep A and B physically separate.
- Connect the battery. Bridge both contacts with one fingertip.
What you should see: The LED lights while touching both contacts. Dry skin may produce a faint response. This switch does not latch.
Try this: Replace 10MΩ with 4.7MΩ. Sensitivity decreases. Keep this experiment battery-powered and separate from other equipment.
Keep learning in order
ProTechTrader is a family-owned US electronics store in New Jersey, serving makers since 2013. We assemble companion component kits for Charles Platt's books.
The Make: Electronics 3rd Edition kits cover these ideas in order alongside the book. Start with Make: Electronics 3rd Edition Kit 1 Economy, for Experiments 1–11, or browse our Make: Electronics 3rd Edition kits and component packs. Follow the book's experiment lists when choosing a kit; this guide uses its own circuit values.
Common questions
What is the easiest electronics project for a beginner?
Start with one LED and a current-limiting resistor powered by a battery. It teaches polarity, current flow, and breadboard connections with only a few parts.
Do I need to solder these circuits?
No. These projects use a solderless breadboard and jumper wires. Choose components with leads or pins that fit the breadboard.
Can I connect an LED directly to a 9V battery?
No. Use a series resistor to limit current. A 1 kΩ resistor is a useful starting value for a standard red indicator LED on a 9V battery.
Why does my breadboard circuit not work?
Disconnect the battery and check the wiring, LED polarity, and component pin assignments. Check whether the power rails have a break in the middle.
Can I use a phone charger instead of a battery?
Keep these builds battery-powered as written. A different supply voltage changes LED current, timer behavior, and other operating conditions.
Do the Make: Electronics kits include the book?
Check the individual listing for the kit or bundle you choose. Do not assume a component kit includes the book.
Keep reading
- How to use a breadboard
- How to use a digital multimeter
- All free how-to guides
- Best electronics kits for adults (2026)
About this guide: ProTechTrader makes and sells the companion component kits for Charles Platt's Make: books, so links to our own products are commercial. Prices and stock for our products are read from the store when this page is rebuilt each night; the product page is always the final word.